Air blow hot or cold on one side – Free Car Help AC

Car air conditioning systems on the one hand, blows hot and cold on the other side is usually a two problems. working from auto repair this short article, a master automotive technicians will share their experiences of air conditioners in Florida over the past few decades. This free information can be equally useful for the do-it-yourselfer as it is to the consumer to recognize the value to be aware of when dealing with repair shops. Read free car A / C help when the hot air blowing on one side.

Generally, cars blow cold on one side of the dashboard and hot on the other side, dual-zone climate control with typically. The dual-zone system allows the driver and front passenger to change to the correct temperature for comfort. Two common causes of temperature differences when both parties are set at the coldest settings using the front cover.

Low refrigerant

134A using

Automotive air conditioners, there is usually a small amount compared to the older cars that use refrigerant R12. Car and truck air conditioners today is much more efficient than older counterparts. The fact that less Freon 134A systems, means that the leak rapidly affect the performance of an HVAC (heating, ventilation, and air conditioning) system. Due to arrangement of the dual AC systems, low refrigerant is the leading cause of the drastic temperature difference between one side of the dash to the other. Even the well-experienced car mechanics may be surprised to learn that only 4-8 ounces of filling 134A can make such a huge difference. The temperature is left to the right slot opening may vary from 10 to 20 degrees. The easiest thing is to try to top off the system or, better yet, remove all Freon and charge your device in the factory fixed amount. In most cases, after the proper freon is responsible for the car, the temp blow as cold as it should on both sides!

What if this does not work? Read on to learn another possible cause of the problem.

HVAC door Issue

The use of the instrument panel made by both sides Dual Zone performing at different temperatures HVAC vents small door in the house. Controlling the door, the temperature of the air to the left and right to adjust the desired comfort level. Many times the motor (or actuator) that controls both sides of the door may fail, or the door itself can break and prevent the church. changing to. Diagnosing this problem is much more complex and can be a subject of another article. Thank you for reading. Hopefully, the free information available to help remedy the problem of "AC blowing hot or cold on one side of the dash."

Source by Dennis Bandy

Air blow hot or cold on one side – Free Car Help AC

Car air conditioning systems on the one hand, blows hot and cold on the other side is usually a two problems. working from auto repair this short article, a master automotive technicians will share their experiences of air conditioners in Florida over the past few decades. This free information can be equally useful for the do-it-yourselfer as it is to the consumer to recognize the value to be aware of when dealing with repair shops. Read free car A / C help when the hot air blowing on one side.

Generally, cars blow cold on one side of the dashboard and hot on the other side, dual-zone climate control with typically. The dual-zone system allows the driver and front passenger to change to the correct temperature for comfort. Two common causes of temperature differences when both parties are set at the coldest settings using the front cover.

Low refrigerant

134A using

Automotive air conditioners, there is usually a small amount compared to the older cars that use refrigerant R12. Car and truck air conditioners today is much more efficient than older counterparts. The fact that less Freon 134A systems, means that the leak rapidly affect the performance of an HVAC (heating, ventilation, and air conditioning) system. Due to arrangement of the dual AC systems, low refrigerant is the leading cause of the drastic temperature difference between one side of the dash to the other. Even the well-experienced car mechanics may be surprised to learn that only 4-8 ounces of filling 134A can make such a huge difference. The temperature is left to the right slot opening may vary from 10 to 20 degrees. The easiest thing is to try to top off the system or, better yet, remove all Freon and charge your device in the factory fixed amount. In most cases, after the proper freon is responsible for the car, the temp blow as cold as it should on both sides!

What if this does not work? Read on to learn another possible cause of the problem.

HVAC door Issue

The use of the instrument panel made by both sides Dual Zone performing at different temperatures HVAC vents small door in the house. Controlling the door, the temperature of the air to the left and right to adjust the desired comfort level. Many times the motor (or actuator) that controls both sides of the door may fail, or the door itself can break and prevent the church. changing to. Diagnosing this problem is much more complex and can be a subject of another article. Thank you for reading. Hopefully, the free information available to help remedy the problem of "AC blowing hot or cold on one side of the dash."

Source by Dennis Bandy

New developments in air conditioning

Air conditioning is not new; in fact, behind the air chemistry was discovered in the 1800's. However, as many of the devices we take for granted in modern society, recent technological advances have changed the nature of this device is made of apartments and offices, making it more convenient, especially in Jacksonville, Florida.

programmable thermostats

Basic air conditioning was simple: a button to turn it on and off, and probably the second control the fan speed. However, technological progress has in common is a programmable thermostat air conditioning units, such as homeowners modify air conditioning maintenance of perfectly chilled environment. These thermostats is that the AC power-saving because it can be programmed to cool only those parts of the home or workplace, you are using, or turned off, while people in the office or away from home.

Cleaner air

Another development in recent years the focus on cleaner air, and the fact that the climate is functioning and functions of the device.

  • Original Freon gas used in air conditioners – or chlorinated, hyrdofluorocarbon hytrogenated or chlorinated primary coolant. These gases are poisonous and themselves.
  • Newer air conditioners are replaced by the standard gases are those that are less damaging to the environment, and from 2010 to less dangerous gases will be standard on all new units.
  • While the HVAC units are simply used to dry heat or cool air, the latest models of air filter can improve air quality and to even reduce the suffering of people with allergies.

The focus on efficiency

Filter air and get rid of harmful freon is not the only way to cool your home or office has changed. New AC units more energy efficient.

  • Since January 2006, the lowest acceptable SEER (Energy Star energy efficiency rating of the board), new central air conditioning system was raised to 13 from the previous low of 10.
  • more units now use fans to continue to blow off the compressor, utilizing the remaining cold air that would otherwise remain unused

Air conditioning is something we often take for granted, especially in Jacksonville, Florida and surrounding areas. However, each time I enjoy the feeling of cool air inside a hot summer day, we should take a moment to appreciate the way that AC was more energy efficient and less harmful to the environment because of a previous developments.

Source by Drew Himel

Air conditioning repair can save more than you think

There is no feeling more annoying than discovering that the temperature rises in the house, and nothing can seem to solve the problem. This is the time to reach out and contact the relevant service and authorized to carry out the necessary air-conditioning repair. Many signal which indicates that the system requires maintenance. Being aware of what these signs can give a reliable gauge to determine whether work will be required.

Some of these symptoms

– Unusual or excessively loud noise when the unit is in operation

– The product cycles are often in and out for no apparent reason

– Slow start or starting error

– The unit does not seem to be cool, and it previously

– Excessive moisture problems, and the whole unit

– High utility costs

While this list may seem daunting, as experienced by evaluation experts can identify the specific cause and offer a variety of options to solve the problem. The costs of climate improvement is actually much smaller than we thought. A fixed time is often several years the life of the air conditioning system and restore it to the level of efficiency we have come to expect. Ignoring the problem or allow you to continue to lead to more expensive repairs or even replace the device that could otherwise have been avoided if the service call was made.

Another advantage of the rapid improvement in the climate that helps to maintain good air quality in your living space or work space. A unit that is damaged or begins to fail reduce air quality and may lead to health problems if not resolved. The services of a licensed, experienced service provider can reduce this unwanted risk and return to the home environment and a healthier state.

One option to explore the provider of a maintenance plan. Scheduling regular maintenance of the air conditioning system off potential problems before they occur, and ultimately saves costs and time in the future. Air conditioning repair – done as a preventive measure – it provides you with a safe knowing that you are getting the maximum benefit of the system is the most economical way.

It should be noted that there are cases where an air conditioning unit can not be repaired and must be replaced instead. While no one enjoys this opportunity to understand the possibilities if a problem discovered can help you decide whether to swap improvement over the preferred solution. Cost, time and convenience for every existing main factors to obtain an impartial assessment of the service company is an important step in this complex process.

Air conditioning repair is much more than just fixing a problem. It is a process, information, explore your options and provide solutions that best interests of the client.

Source by Aaliyah Arthur

AC is not cooling While the Stop – blow hot air at idle

There are several reasons why a car AC is not cool when you stop blowing cool and just move. The most common reason for the condenser cooling fan is not working. It is important to know that many times the fan share the radiator and the condenser, even when other twin. The reason why the cooling fan may be bad effects on AC, thus drastically by the fact that the heat of the cooling medium (freon) is usually cooled as it passes through the condenser. So even if the condenser fan does not work, it does not affect the AC, while the car passes the highway speed . This is because the air passes through the condenser, when driving down the road, so that the fan is not required. When the car to a stop, the capacitor is completely dependent on the cooling fan to cool down. Sometimes the fan works, but it may be moving too slowly to sufficiently cool the condenser. To check engine light is a test used to check the growing power and ground from the power outlet. If power and ground are present, and the engine is not running, the motor circuit is open. If the cooling fan motor is worn, you can get started sometimes temporarily lightly touch the fan motor with a small hammer or wrench. If the fan is switched on when this is done, the engine turns will be needed. This is just another way to make sure that you get the power needed to drive it. Also keep in mind that the cooling fan start at any time (some even come in addition to motor) so be careful that you do not stick to your hands, as the blade! Note that if the cooling fan motor has seized, it is likely that the fuse is blown. So, if there is no power to the fan and the motor is locked, the security will more than likely need to be replaced during the fan motor replacement.

other causes Cool Car AC is not in neutral or stop

  1. The car may be overheating – caused by something else to use as a cooling fan.
  2. heat transfer from the radiator and the cooling efficiency can change if the car overheating.
  3. The AC compressor is not pumping sufficiently slowed RPM (revolutions per minute).
  4. expansion valve can not be regulated to the cooling medium.
  5. the capacitor can be bent or hinder foreign debris capacitor until

  6. .

There are special combs to straighten fin condenser condenser fins. But in my experience, bent condenser fins is not so much a common problem. The most common problem when you drive in the country, pollen accumulated over time between the ribs. Garbage on the road like a piece of paper or plastic bag to prevent part of the capacitor reduces the performance can happen anywhere. It's funny to me that during my time as an auto technician what the consumer is worried that the AC is not cooling, but did not realize that the car is overheating – even when the thermometer pegged!

Source by Dennis Bandy

AC is not cooling While the Stop – blow hot air at idle

There are several reasons why a car AC is not cool when you stop blowing cool and just move. The most common reason for the condenser cooling fan is not working. It is important to know that many times the fan share the radiator and the condenser, even when other twin. The reason why the cooling fan may be bad effects on AC, thus drastically by the fact that the heat of the cooling medium (freon) is usually cooled as it passes through the condenser. So even if the condenser fan does not work, it does not affect the AC, while the car passes the highway speed . This is because the air passes through the condenser, when driving down the road, so that the fan is not required. When the car to a stop, the capacitor is completely dependent on the cooling fan to cool down. Sometimes the fan works, but it may be moving too slowly to sufficiently cool the condenser. To check engine light is a test used to check the growing power and ground from the power outlet. If power and ground are present, and the engine is not running, the motor circuit is open. If the cooling fan motor is worn, you can get started sometimes temporarily lightly touch the fan motor with a small hammer or wrench. If the fan is switched on when this is done, the engine turns will be needed. This is just another way to make sure that you get the power needed to drive it. Also keep in mind that the cooling fan start at any time (some even come in addition to motor) so be careful that you do not stick to your hands, as the blade! Note that if the cooling fan motor has seized, it is likely that the fuse is blown. So, if there is no power to the fan and the motor is locked, the security will more than likely need to be replaced during the fan motor replacement.

other causes Cool Car AC is not in neutral or stop

  1. The car may be overheating – caused by something else to use as a cooling fan.
  2. heat transfer from the radiator and the cooling efficiency can change if the car overheating.
  3. The AC compressor is not pumping sufficiently slowed RPM (revolutions per minute).
  4. expansion valve can not be regulated to the cooling medium.
  5. the capacitor can be bent or hinder foreign debris capacitor until

  6. .

There are special combs to straighten fin condenser condenser fins. But in my experience, bent condenser fins is not so much a common problem. The most common problem when you drive in the country, pollen accumulated over time between the ribs. Garbage on the road like a piece of paper or plastic bag to prevent part of the capacitor reduces the performance can happen anywhere. It's funny to me that during my time as an auto technician what the consumer is worried that the AC is not cooling, but did not realize that the car is overheating – even when the thermometer pegged!

Source by Dennis Bandy

Air conditioning repair can save more than you think

There is no feeling more annoying than discovering that the temperature rises in the house, and nothing can seem to solve the problem. This is the time to reach out and contact the relevant service and authorized to carry out the necessary air-conditioning repair. Many signal which indicates that the system requires maintenance. Being aware of what these signs can give a reliable gauge to determine whether work will be required.

Some of these symptoms

– Unusual or excessively loud noise when the unit is in operation

– The product cycles are often in and out for no apparent reason

– Slow start or starting error

– The unit does not seem to be cool, and it previously

– Excessive moisture problems, and the whole unit

– High utility costs

While this list may seem daunting, as experienced by evaluation experts can identify the specific cause and offer a variety of options to solve the problem. The costs of climate improvement is actually much smaller than we thought. A fixed time is often several years the life of the air conditioning system and restore it to the level of efficiency we have come to expect. Ignoring the problem or allow you to continue to lead to more expensive repairs or even replace the device that could otherwise have been avoided if the service call was made.

Another advantage of the rapid improvement in the climate that helps to maintain good air quality in your living space or work space. A unit that is damaged or begins to fail reduce air quality and may lead to health problems if not resolved. The services of a licensed, experienced service provider can reduce this unwanted risk and return to the home environment and a healthier state.

One option to explore the provider of a maintenance plan. Scheduling regular maintenance of the air conditioning system off potential problems before they occur, and ultimately saves costs and time in the future. Air conditioning repair – done as a preventive measure – it provides you with a safe knowing that you are getting the maximum benefit of the system is the most economical way.

It should be noted that there are cases where an air conditioning unit can not be repaired and must be replaced instead. While no one enjoys this opportunity to understand the possibilities if a problem discovered can help you decide whether to swap improvement over the preferred solution. Cost, time and convenience for every existing main factors to obtain an impartial assessment of the service company is an important step in this complex process.

Air conditioning repair is much more than just fixing a problem. It is a process, information, explore your options and provide solutions that best interests of the client.

Source by Aaliyah Arthur

Air conditioning system – primitive to sophisticated

The Romans water treatment. They knew the pleasures of sitting in a cool well, but it was the ancient Egyptians who started refining the first air conditioning system.

The Egyptians were in the Nile River in the River of Life in many ways. Not only is it provides water for drinking and bathing, but it has allowed farming, the otherwise arid landscape. In addition to the Nile provided water for the first evaporative cooling on a large scale.

The Ages, people knew that putting water tank semi-porous, unglazed clay pot than one, resulting in a cold drink because of evaporative cooling. The Egyptians kicked it up a notch when they built walls and sheets of water cascading over that. Slaves with huge fans stood close by and kept the air circulating through the moving water. The result of the evaporation cooling.

Several ancient cultures also used "wet carpet." We know that the Egyptians, Romans and Greeks used both wet carpet in the air inside homes and other buildings cool. When a thick, damp cloth hung over the doors and / or windows, the air movement effectively promote evaporative cooling and reduce the indoor temperature is even lower, about 66 ° Fahrenheit. The Egyptians have figured out how to make the ice!

In the first days of conditioning, especially in the US, evaporative cooling is still widespread use in dry areas. The cube, adobe-style houses, the Southwest is often the roof structure is designed to support the weight of a large shallow lake. The roof is flooded, the fan blows the dry air in the liquid which accelerates evaporation. The cooled air then passes through the building, a welcome relief in the hot summer months. These coolers, sometimes called "swamp coolers" economical operation and are still in use in some areas.

Modern air conditioning systems no longer rely on water evaporation cooling. Gases, such as Freon refrigerants modern Puro or that reduce the air temperature. The actual air conditioner is usually placed outside the building because it is a harmless and effective way to get rid of internal heat (the atmosphere).

An important function in today's AC system to reduce the humidity inside the structure. Keeping the humidity low (30% of the area) and reduces mold problems, and help alleviate the serious health problems for people who suffer from allergies. Furthermore, heavy dust mite survival low humidity.

When conditioning unit is up and running, it works to maintain a pressure level of the whole structure. In order to work effectively the unit, doors and windows must be closed so that pressure can remain as constant as possible. Spot cooling, pick up a small fan to move the air where you need to get out of your comfort level.

Source by Brian Figlioli

New developments in air conditioning

Air conditioning is not new; in fact, behind the air chemistry was discovered in the 1800's. However, as many of the devices we take for granted in modern society, recent technological advances have changed the nature of this device is made of apartments and offices, making it more convenient, especially in Jacksonville, Florida.

programmable thermostats

Basic air conditioning was simple: a button to turn it on and off, and probably the second control the fan speed. However, technological progress has in common is a programmable thermostat air conditioning units, such as homeowners modify air conditioning maintenance of perfectly chilled environment. These thermostats is that the AC power-saving because it can be programmed to cool only those parts of the home or workplace, you are using, or turned off, while people in the office or away from home.

Cleaner air

Another development in recent years the focus on cleaner air, and the fact that the climate is functioning and functions of the device.

  • Original Freon gas used in air conditioners – or chlorinated, hyrdofluorocarbon hytrogenated or chlorinated primary coolant. These gases are poisonous and themselves.
  • Newer air conditioners are replaced by the standard gases are those that are less damaging to the environment, and from 2010 to less dangerous gases will be standard on all new units.
  • While the HVAC units are simply used to dry heat or cool air, the latest models of air filter can improve air quality and to even reduce the suffering of people with allergies.

The focus on efficiency

Filter air and get rid of harmful freon is not the only way to cool your home or office has changed. New AC units more energy efficient.

  • Since January 2006, the lowest acceptable SEER (Energy Star energy efficiency rating of the board), new central air conditioning system was raised to 13 from the previous low of 10.
  • more units now use fans to continue to blow off the compressor, utilizing the remaining cold air that would otherwise remain unused

Air conditioning is something we often take for granted, especially in Jacksonville, Florida and surrounding areas. However, each time I enjoy the feeling of cool air inside a hot summer day, we should take a moment to appreciate the way that AC was more energy efficient and less harmful to the environment because of a previous developments.

Source by Drew Himel

Air conditioning system – primitive to sophisticated

The Romans water treatment. They knew the pleasures of sitting in a cool well, but it was the ancient Egyptians who started refining the first air conditioning system.

The Egyptians were in the Nile River in the River of Life in many ways. Not only is it provides water for drinking and bathing, but it has allowed farming, the otherwise arid landscape. In addition to the Nile provided water for the first evaporative cooling on a large scale.

The Ages, people knew that putting water tank semi-porous, unglazed clay pot than one, resulting in a cold drink because of evaporative cooling. The Egyptians kicked it up a notch when they built walls and sheets of water cascading over that. Slaves with huge fans stood close by and kept the air circulating through the moving water. The result of the evaporation cooling.

Several ancient cultures also used "wet carpet." We know that the Egyptians, Romans and Greeks used both wet carpet in the air inside homes and other buildings cool. When a thick, damp cloth hung over the doors and / or windows, the air movement effectively promote evaporative cooling and reduce the indoor temperature is even lower, about 66 ° Fahrenheit. The Egyptians have figured out how to make the ice!

In the first days of conditioning, especially in the US, evaporative cooling is still widespread use in dry areas. The cube, adobe-style houses, the Southwest is often the roof structure is designed to support the weight of a large shallow lake. The roof is flooded, the fan blows the dry air in the liquid which accelerates evaporation. The cooled air then passes through the building, a welcome relief in the hot summer months. These coolers, sometimes called "swamp coolers" economical operation and are still in use in some areas.

Modern air conditioning systems no longer rely on water evaporation cooling. Gases, such as Freon refrigerants modern Puro or that reduce the air temperature. The actual air conditioner is usually placed outside the building because it is a harmless and effective way to get rid of internal heat (the atmosphere).

An important function in today's AC system to reduce the humidity inside the structure. Keeping the humidity low (30% of the area) and reduces mold problems, and help alleviate the serious health problems for people who suffer from allergies. Furthermore, heavy dust mite survival low humidity.

When conditioning unit is up and running, it works to maintain a pressure level of the whole structure. In order to work effectively the unit, doors and windows must be closed so that pressure can remain as constant as possible. Spot cooling, pick up a small fan to move the air where you need to get out of your comfort level.

Source by Brian Figlioli